March22

National Ladder Safety Month

April is National Ladder Safety Month

Did you know…

  • $17.1 billion is spent on workplace falls
  • Falls are in the top 3 most disabling workplace injuries
  • Ladders are #6 on OSHA’s Top 10 Most Cited Violations list

Using Ladders

Choose the right type and size ladder. Except where stairways, ramps, or runways are provided, use a ladder to go from one level to another. Keep these points in mind:

  • Be sure straight ladders are long enough so that the side rails extend above the top support point, by at least 36 inches.
  • Don’t set up ladders in areas such as doorways or walkways where others may run into them, unless they are protected by barriers. Keep the area around the top and base of the ladder clear. Don’t run hoses, extension cords, or ropes on a ladder and create an obstruction.
  • Don’t try to increase the height of a ladder by standing it on boxes, barrels or other materials. Don’t try to splice two ladders together.
  • Do not apply personal or job stickers/decals.
  • Set the ladder on solid footing against a solid support. Don’t try to use a stepladder as a straight ladder.
  • Place the base of straight ladders out away from the wall or ledge of the upper level about 1 foot for every 4 feet of vertical height. Don’t use ladders as a platform, runway, or scaffold.
  • Tie in, block or otherwise secure the top of straight ladders to prevent them from shifting.
  • To avoid slipping on a ladder, check your shoes for oil, grease, or mud and wipe it off before climbing.
  • Always face the ladder and hold on with both hands when climbing up or down. Don’t try to carry tools or materials with you.
  • Don’t lean out to the side when you’re on a ladder. If something is out of reach, get down and move the ladder over.
  • Most ladders are designed to hold only one person at a time. Use by two workers may cause the ladder to fail or throw the ladder off balance.

Inspecting Ladders

Before using any ladder, inspect it. Look for the following faults:

  • Loose or missing rungs or cleats
  • Loose nails, bolts, screws
  • Wood splinters or damaged edges
  • Cracked, broken, split, dented or badly worn rungs, cleats or side rails
  • Corrosion of metal ladders or metal parts

If you find a ladder in poor condition, tag the ladder and take it out of service. If repairs are not feasible, it should be removed from the jobsite.

NOTE: Always promote a discussion on any of the topics covered in the Tool Box Talks. Should any question arise that you cannot answer, don’t hesitate to contact your Employer.

Shepformation... The Shepley Newletter

  • NYLE Robert J. Horne Jr. CHIPS Award

    The Northeastern Young Lumber Execs (NYLE) recentl

    Read More
  • Tony and Lorraine Shepley Awarded Joshua A. Nickerson Society Award

    On June 18th the Cape Cod Chamber of Commerce host

    Read More
  • 24th Annual Shepley Wide Open

    The employees at Shepley are teeing up for the 24t

    Read More

Central Location:

Shepley

216 Thornton Drive, Hyannis, MA 02601
Phone: 508-862-6200
Toll-free: 800-227-7969
Facsimile: 508-862-6012
Directions

Shepley Showcase

75 Ben Franklin Way, Hyannis, MA 02601
Phone: 508-771-7227
Toll-free: 877-909-7227
Facsimile: 508-771-7044
Directions

Nantucket Office

6 Lovers Lane, Nantucket, MA 02554
Phone: 508-325-0400
Facsimile: 508-325-0359
Directions

Wellfleet Office

2238 Route 6, Wellfleet, MA 02667
Phone: 508-349-2280
Facsimile: 508-349-3078
Directions