Quarter Sawn Lumber

by Peter Iodice

One of the most commonly confused products in the building materials industry is quarter sawn lumber. Simply stated, it’s actually just how a log is cut.

plan sawn log

With plain sawn material the log is cut vertically as shown in the pictures above and below.  This maximizes the yield out of a log with very little waste and you achieve the widest boards possible.  When a log is plain sawn you are cutting vertically across the growth rings of the tree. This leaves an arched end grain that wants to force the board to cup when moisture enters and exits the board.  Imagine a house load of white oak flooring laid out in a new home in our Cape Cod climate. Moisture will be constantly entering and exiting the boards and the potential for cupping is accelerated, especially in wider boards.

plain sawn graphic

plain and quarter sawn graphic

With quarter sawn material the log is literally quartered. A log is cut in quarters then sawn perpendicular to the growth rings of the tree. By cutting the log this way you have less yield out of a log, more waste and you are limiting the max width of the boards you can achieve from a log.  So in a world of limiting waste, maximizing yield (and therefore profits) why would anyone quarter a log?  Performance is the answer.  As I mentioned earlier, the log is cut perpendicular to the growth rings of the tree. This leaves the end grain at a 90 degree angle to the face of the board. With quarter sawn material the boards cannot cup. In red & white oak quarter sawn (most commonly used for flooring on Cape) it also creates a gorgeous fleck pattern on the face of the board (see pic below). Quarter sawn red and white oak are truly superior products, especially when the end use is flooring and is located in the moisture rich climate we live in on Cape Cod.

quarter sawn flecks

Visit the “shepleywood” YouTube channel to see a great video from Wood Workers Guild of America, in our “Building Materials” playlist, that clearly and simply shows the cuts of a log and the differences between plain sawn, quarter sawn and rift sawn lumber.



Below is a beautiful picture, from our very own Lauren Amster, of a quarter sawn white oak board in your Shepley mill shop here in Hyannis. This board was supplied to us by our partner vendor Rex Lumber “The King of Imported and Domestic Hardwood Lumber” http://www.rexlumber.com/lumber. Rex has the network and ability to source materials from the best mills across the country and they are one of the largest wholesalers on the east coast. At Shepley we are proud to have them as a partner vendor, a resource for you the builder and the end consumer homeowner. Please feel free to contact your Shepley rep anytime for more information on quarter sawn red and white oak flooring for your next project.

quarter sawn log

Peter Iodice started with Shepley in 2004. He has worked his way from Receiving and Quality Control to Outside Interior Trim Sales, covering the Cape & South Shore. Peter is backed inside by Lauren Amster.

You can reach Peter and Lauren at 508-862-6225.


Shepformation... The Shepley Newletter

  • Civic Rent: Beer for a Good Cause

    Where to Buy Civic Rent is a limited edition lager

    Read More
  • 5 Reasons to Consider Garapa for Your Next Deck

    By Jaime Romkey When it comes to choosing the righ

    Read More
  • Winter Weather Safety

    By John Howell Winter Weather Slips/Trips/FallsSli

    Read More

Newsletter Sign Up

Central Location:

Hyannis Office

216 Thornton Drive, Hyannis, MA 02601
Phone: 508-862-6200
Toll-free: 800-227-7969
Facsimile: 508-862-6012

Shepley Showcase

75 Ben Franklin Way, Hyannis, MA 02601
Phone: 508-862-6228
Toll-free: 877-909-7227
Facsimile: 508-862-6047

Nantucket Office

6 Lovers Lane, Nantucket, MA 02554
Phone: 508-325-0400
Facsimile: 508-325-0359

Wellfleet Office

2238 Route 6, Wellfleet, MA 02667
Phone: 508-349-2280
Facsimile: 508-349-3078